Clarus-environmental Container Assembly Bedienungsanleitung PDF herunterladen

All Clarus Environmental products must be installed and maintained in accordance with all applicable codes.

Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies.

1. Dig a 36" minimum hole and remove a 23" section of the discharge

pipe. Clean both ends of the exposed pipe.

2. Therearetwosizesofpipesealsincludedwiththeltercontainer.

The larger seals are for SCH 40-4" PVC, and the smaller seals are

for SDR 35-4" PVC. Install the appropriate pipe seal in the basin so

that the pipe will slide in from the outside of the basin.

3. Cut and clean an 11" length of pipe from the 23" section of 4" pipe

you removed from the discharge line. Cement a 4" coupling to one

end of this pipe. The coupling will be used to reconnect the 11"

length of pipe to the existing pipe on the distribution side of the

basin. Insert the pipe into outlet pipe seal, keeping the coupling on

the outside. Note: To ease installation, lubricate the seal with a mild

soap solution such as dishwashing liquid.

4. Place 3" of sand or gravel in the hole. Place the basin in the hole,

andadjustllasneededtolineupthepipecomingfromtheseptic

tank and the inlet hole on the basin. Insert the pipe coming from the

septic tank into the inlet of the basin. The pipe should extend into the

basin approximately 1".

5. Prepare the coupling and pipe for cementing, then push outward

on the outlet pipe and cement the coupling to the existing pipe. The

pipe should extend into the basin approximately 3". Note: After pipe

is installed, clean off any remaining lubricant.

6. Toinstallthelter(P/N170-0078),cementa4"sanitaryteeonto

the outlet pipe with a 12" length of 4" pipe cemented to the bottom

opening of the sanitary tee. If using a Clarus Environmental WW1

Filterwithsanitarytee(P/N170-0144),removethelterfromthe

sanitary tee. Cement the sanitary tee on to the pipe extending into

the outlet of the basin. If the piping is SDR 35 use the reducer

suppliedwiththelter.Slidethelterbackintothesanitarytee.

7. Attachthe12"extensionrisertothebasinusingthesuppliedfoam

gasket and bolts. Apply silicone caulking over the bolt and washer

afterinstalled.(Optional6"and12"extensionrisersareavailable

tobeaddedtothe12"extensionasneeded.)

8. Attachthecovertotheextensionusingthesuppliedfoamgasket

and bolts.

9. Backlltothetopoftheextension.

SECTION: C2.10.170

CL0044

1011

Supersedes

New

3649 Cane Run Road

Louisville, KY 40211-1961

877

244

9340

Fax: 877

414

4316

www.clarusenvironmental.com

Container Assembly

INSTALLATION INSTRUCTIONS

EXISTING

DISCHARGE PIPE

12" RISER

SEPTIC TANK

COVER

PIPE SEAL

FILTER

BASIN

FILTER CONTAINER

11" LONG PIECE OF PIPE

THAT WAS CUT OUT

4" COUPLING

(SUPPLIED BY OTHERS)

EXISTING

DISTRIBUTION BOX

APPLY FOAM GASKET AND

FASTEN DOWN WITH SCREWS

4" SANITARY

TEE

4" PVC PIPE

12"

EXISTING

SEPTIC TANK

EXISTING

DISCHARGE

PIPE

CUT AND

CLEAN PIPE

EXISTING

DISTRIBUTION BOX

5 1/2

36 MIN.

7 1/2

sk2298

Inhaltsverzeichnis

Seite 1 - INSTALLATION INSTRUCTIONS

All Clarus Environmental products must be installed and maintained in accordance with all applicable codes.Product information presented here reflects

Kommentare zu diesen Handbüchern

Keine Kommentare

Clarus-environmental Container Assembly Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör fürs Wasser Clarus-environmental Container Assembly herunter. Clarus Environmental Container Assembly User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zubehör fürs Wasser Clarus-environmental Container Assembly